| Function code | Name | Description | Default | Property |
| 47 Group solar pumping special group |
| P00.03 | RESET | 0:NO ACTION 11:Restore default parameter except for motor parameter and
auto-tune related parameter and factory parameter 12:Restore default to factory parameter 13:Clear tripping record | 0 | ★ |
| P00.06 | Source of the Operation Command | 0:keypad 1:terminal 2:communication Ø Command source: run,stop,forward,reverse,jog,fast brake stop.etc | 0 | ★ |
| P00.07 | Numeric frequency setting | 00.00Hz～maximum frequency | 50.00Hz | ☆ |
| P00.11 | Application Macro | 00001:Output three phase 50HZ 00002:Output three phase 60hz 00021:Output single phase with capacitor 50hz 00022:Output single phase with capacitor 60hz 00031:Output single phase without capacitor 50hz 00032:Output single phase without capacitor 60hz | 00000 | ★ |
| P01.06 | Maximum frequency | 10.00～600.00Hz | 50.00Hz | ★ |
| P01.08 | Upper limit frequency | Lower limit frequency-maximum frequency | 50.00Hz | ☆ |
| P07.03 | Relay 1 Output terminal function group(T1A T1B T1C) | 0:No function 1:READY 2:RUN 3:Error1(stop fault) 4:Error2(same as Error1 except undervoltage) 5:Warning output(fault but in running) | 3 | ☆ |
| P11.01 | AC asynchronous motor TYPE | 0:Three phase AC asynchronous motor 1:Single phase AC asynchronous motor without starting capacitor | 0 | ★ |
| P11.02 | Motor rated power | 0.1kW～710.0kW Ø when power is less than 1kw ,0.75kw set to 0.8 as per round up
principle ,0.55kw motor set 0.6 Ø when change motor rated power,AC drive will automatically set
other parameter of motor name plate and motor model parameter be careful to use | Depend | ★ |
| P11.03 | Motor rated voltage | 10V～2000V | Depend | ★ |
| P11.04 | Motor rated current | P11.02<30kW:0.01A P11.02>=30kW:0.1A | Depend | ★ |
| P11.05 | Motor rated frequency | 1.00Hz～600.00Hz | 50.00Hz | ★ |
| P11.06 | Motor rated RPM | 1～60000rpm | Depend | ★ |
| P21.00 | Monitoring display | 0:Standard mode (display frequency only) 1:Automatic scrolling display(Check 3.1 in detail )it show
hz,current,power and voltage | 0 | ★ |
| P23.15 | Output phase loss function | 0.0-30%, 0% means output phase detections shielded | 30% | ☆ |
| r27.15 | Accumulative running time | Unit:hour
| | ● |
| P47.00 | Solar pump Mppt function enable | 0: invalid The parameters behind the 47 group cannot be changed! 1: Enable, to enable the special mppt function of the PV pump
inverter
| 1 | ★ |
| P47.01 | Solar pump control mode
| Units digit’s: Startup mode 0: Manual start, the start mode is determined by P00.06; 1: automatic start, When P00.06 change, the association changes here. P00.06=0, when inverter starts and stops by keypad control, it is
automatically modified to 1-automatic start P00.06=1, when inverter starts and stops by terminal control.it is
automatically changed to 0-manual start Ten digit’s: MPPT function 0: MPPT is disabled; CVT control is used (voltage is given as
P47.04). 1: Enable MPPT. Hundred’s unit automatic switching function 0: prohibited 1: enable Automatic switching is enabled, when the light is weak, it will
automatically switch to the electric supply, and the MPPT function
is disabled at this time. | 011 | ★ |
| P47.03 | Automatic start timing | In auto start mode, set the time from power on to start. It is also
waiting time to start | 600 | ★ |
| P47.04 | MPPT starting voltage | Set the starting voltage of the MPPT algorithm. When the MPPT function is disabled, this value is the reference
voltage. | 305V(530V) | ★ |
| P47.05 | Light detection threshold | If the output frequency is lower than this value and exceeds
P47.06, it will be reported to Sleep and stop If automatic switching is enabled, it will switch to ac grid
operation, and the MPPT function will be disabled | 0Hz | ☆ |
| P47.06 | Light detection time | See P47.05 for explanation. | 60s | ☆ |
| P47.07 | Light weak wake up time | After the sleep fault is reported, if the time when Vdc is higher
than the undervoltage point is greater than the set value, the
fault state is exited and the operation continues. When the automatic switching is enabled, after switching into the
electric supply operation for this time, it will try to switch into
the photovoltaic operation. | 600s | ☆ |
| P47.08 | MPPT tracking step length | The amount of change in the bus voltage during an MPPT cycle. The
larger the value, the faster the maximum power point is found, but
the lower the accuracy of the maximum power point. | 2V | ☆ |
| P47.09 | Regulator proportional gain | 0.001~1.00 It is for immediate response speed, it is not
recommended to change | 0.05 | ☆ |
| P47.10 | Regulator integral gain | 0.001~0.100 tracking response.it is not recommended to change | 0.05 | ☆ |
| P47.28 | Starting coefficient | 0.000～1.000 | 0.850 | ☆ |
| P47.30 | Fast speed function | Unit digit:fast starting 0:Disable 1:Enable Ten digit:Fast mppt tracking 0:Disable 1:Enable | 11 | ☆ |
